Sound familiar?Churchill
- The call
- Every morning the front door key needs the same little dance: push in, lift, wiggle, turn. It has been getting worse for a year, and this week it took three tries in the cold before the deadbolt finally gave.
The keys the seller handed over came in a sandwich bag: six unlabelled copies for two locks of different makes from different decades. You have no idea how many more copies exist or who is holding them.
In plain words
After a break-in or an attempt, the door tells a story, and the new hardware should answer it. Splintered wood around the strike means the jamb gave before the lock did, so the repair pairs a heavier deadbolt with a reinforced strike and 75 millimetre screws that reach the framing behind the jamb. A bent bolt or cracked housing is replaced with a graded deadbolt whose bolt has a hardened core. A knob lock that was bumped or forced is swapped for a set with better pins. The aim is a whole opening that resists force, not merely a shinier lock.
Lock Replacement & Upgrade · Churchill
How the visit goes
Scene 1
Exposure, weather and finish
The locksmith looks at where the door lives. A side entrance beside a salted driveway, a south-facing front door in full sun and a sheltered porch each treat a finish differently, and the residential hardware label scores finish durability as its own category for exactly this reason. Existing hardware is examined for pitting, peeling and green bloom, which shows how hard the spot is on metal. That guides the choice between a PVD brass, a satin nickel, a powder-coated black or a stainless product, and whether a storm door or a small hood would help. Matching the rest of the entrance comes last, once the finish will survive the location.
Scene 2
Stepping up the grade of a deadbolt
When the brief is a stronger door, the new deadbolt is chosen for what is inside it: a bolt with a full 25 millimetre throw and a hardened steel insert that spins against a saw, a housing that stands low so a wrench has nothing to grip, and a cylinder with pins that resist picking and bumping. Fitting follows the normal steps, but the locksmith confirms the bolt reaches full extension with the door closed, because a high-grade bolt seated halfway into a shallow pocket behaves like a low-grade one. The strike is upgraded alongside it so both halves of the lock share the same standard.
Scene 3
A clear plan for the remaining doors
Most households do not replace every lock in one visit, and you leave with a short list of what is left, in order of importance. Typically the front door and the garage-to-house door come first, then the back and side doors, then the patio slider and interior sets. Because the key plan has been settled, any lock added later can be pinned to the same key, so the house stays on one key as the work continues. Finishes and styles are recorded so future hardware matches. The first visit sets the standard; the rest of the house can follow when it suits you.
In the van
- Reinforced strike plate and strike box
- Handleset with matching deadbolt
- Manufacturer-approved cylinder lubricant
- Filler plates and thick-door extension kits
- Cylinders, plug follower and pinning kit
What shapes the quoteBell Ewart Lock Services
- Strike reinforcement and jamb repair
- A reinforced strike with long screws is a modest addition; repairing a jamb split from a forced entry, or fitting a strike box into a frame that has never had one, adds labour and materials.
- Condition of the old hardware
- Hardware that comes off cleanly is one thing; painted-over trim, seized or stripped screws and a cylinder that has to be drilled out add time before the new lock can go on.
- Number of doors
- One back door is a small visit; the front, back, side, garage man-door and patio slider together are a longer one, though several doors done at once share the travel and setup.
FeesSame any hour
Ask us anything about locks
Is there anything different about steel or fibreglass doors?
The lock hardware is the same; the door construction changes the method. Steel and fibreglass doors have a wooden or composite block inside the lock stile, and existing bores are used wherever possible. Where a new deadbolt must be added, the locksmith drills with a jig and bits suited to the skin so the hole is clean and square, and fits an edge plate designed for that door. Insulated doors also move less with humidity, so alignment tends to hold well.
Is a smart lock a good upgrade, and what happens when the batteries run out?
For a household with many people coming and going, codes that can be added and removed are a real convenience. Behind the keypad it is still a deadbolt, so grade and strike matter as much as ever. Batteries typically last months and the lock warns you as they fade; depending on the model, a dead battery is handled with a mechanical override key or with external contacts for a temporary power source, so it is worth confirming which one your lock uses.
My old house has a mortise lock. Can it take modern hardware?
Often the original case can be kept and given a new cylinder and strike, which keeps the period look and the old door intact. Where the case is beyond service, a filler or conversion plate covers the mortise pocket and lets a cylindrical deadbolt or knob set be fitted without cutting into the door's stile. The locksmith looks at the door before recommending either path, since old doors vary a great deal.
Change or Rekey Locks
- Deadbolt InstallationThe old deadbolt has grown lazy.
- Vintage Mortise Lock ServiceThe key turns freely in the round cylinder on the door, all the way around and back, without the bolt shifting at all.
- Smart Lock InstallationArthritis has made the small house key hard to grip and turn, especially with gloves on in January.
- Gate & Building Entry LocksBetween the front gate, the side gate and the one behind the shed, there are three different padlocks, three different keys, and…
- Mailbox Lock ReplacementAfter a winter of road spray and salt, the little lock on the mailbox door has gone stiff, then gritty, then almost immovable.
Churchillinformation
SimcoeOntario
Lock Replacement & Upgrade · Innisfil, Bell Ewart, Big Bay Point, Cedar Harbour, Cookstown, Innisfil Park, Killarney Beach, Leonards Beach, Nantyr Park, Stroud, Alcona, Alderslea, Bear Point, Belle Air Beach, Big Cedar Point, Cedar Mount, Crescent Harbour, De Grassi Point, Glenwood Beach, Lefroy, Mooselanka Beach, Peninsular Park, Sandy Cove, Tent City
- Town
- Churchill, Simcoe
- In business
- 24 years
- Hours
- Open 24/7
- Nights, weekends and holidays, same fees
- Phone
- (249) 315-0368
- Visits
- On-site assessment preferred. Request a visit or call.
2021 census: what it means at the door
Every square is one home in a hundred.
- 35 in 100 homes · mixed ages
- 90 in 100 homes · mostly houses
- About 35% of homes in Innisfil were built in 1980 or earlier, according to the 2021 Census.A mix of eras means a mix of bores and backsets. Standard modern sizes on one door, older dimensions on the door across the street. Carrying adapter plates and cylinders in both ranges lets a locksmith fit upgrades cleanly to either.
- Single-detached houses make up about 90% of homes in Innisfil (2021 Census).Detached houses have their own garages, sheds and gates, and each tends to carry a lock chosen on the day it was needed. A locksmith visiting such a home looks at all of them, not just the front door, and brings the whole property up to one standard.
Nearby
On-site assessment
Request a visit.
The keys the seller handed over came in a sandwich bag: six unlabelled copies for two locks of different makes from different decades.
(249) 315-0368, open 24/7.